Yield Strength Performance：9
Light Weight Level：8
Acid and Alkali Resistance Level：7
Shear Strength Performance with Friction Materials：10
NVH Level (Noise/Viberation/Harshness)：8
Environmental Protection Index：7
* High index means good performance, the higher the better. 10 is the highest.
|Not Enough Bonding Power Between Back Plates and Friction Materials||Easy to Cause Cracking on Brake Pads|
|Hard to Control the Thickness of Glue||Not Enough Shear Strengh For High-End Cars|
|The Quality of Glue Is Uncontrollable||Lower Safety Guarantee|
|Not Stable Gluing Performance With Painting||Unstable Braking Performance During Driving|
|Not Enough High Temperature Resistance||Short Working Life for Brake Pads|
|Higher Bonding Performance and No Need Gluing Before Production|
|Stable Braking Performance During Your Driving|
|Longer Working Life of Your Brake Pads|
|Safety Guarantee for Your Life|
|Adapt To Different Conditions of Roads|
|1. Height: 1.70mm±0.3mm|
|2. Shovel Mouth After Hook Provide Stronger Shear Strength|
|3. Width of Hooks: 2.0mm±0.2mm|
|4. Distance Between Hooks Lines: 4.0mm-6.0mm|
|5. Distance Between Two Hooks: 6.0mm|
ENHANCED BONDING TECHNOLOGY
1. Backing Plates is designed and made by UAI's latest URT(UAI Mechanical Retention Technology) solution, the surface of friction side is full of hooks, with height over 1.5mm.
2. Hooks will dig into the friction materials, deeply rooted, thus to improve the shear bonding strength greatly.
3. Shear Force up to 45KN, combinding with gluing technology. Very suitable for the high-speed and high-horsepower rally matches.
4. Glue will cover the full surface of backing plates, greatly improving the bonding strength between the friction material and the steel back
1. Using high-quality Q235B carbon steel, with high yield points at 235MPa, no possible to bend during the braking.
2. Thickness is uniform, flatness is controlled within 0.1-0.2mm;
3. Quality is stable and consistent
4. Molds are manufactured according to the FMSI standard drawings;
5.Strictly produced, accurate size to match for the OE brake capilers and brake discs;
6. Perfectly fit in the caliper, thus reduce the noise caused by friction with the caliper accessories during braking.
All the backing plates will be neatly stacked into a wooden pallet, if backing plates with hooks, they will be stacked hooks to hooks to prevent the outer surface scratch.
All the backing plates will be wrapped with anti-rust paper or film to prevent from moisture during the sea or air transportation.
Besides the anti-rust paper or film, absorbent drying bags will also be put into the pallet to absorb moisture during the transportation.
The raw material of the fumigation-free pallet is composite board or plywood, and the raw material is formed by high-temperature and high-pressure sterilization of various wooden residual materials.
The wooden box adopts a reinforced structure, and there are reinforced wooden boards all around. The structure is optimized to make the whole wooden box more reasonable and firm, and it is not easy to fall apart and break.
There is iron sheet reinforcement around the wooden pallet to prevent it from falling apart due to the heavy steel backing plates.
After packing, the whole pallet will use Reinforced PET Packing Belt to make a third protection.
At last, the whole pallet will be covered by moisture prevention films to stop the rain or water during transportation in the first stage.
There will be a shipping mark on each pallet for sea transportation and logistic purposes, also easy for you to trace and identify.
We export about 300 Containers Each Year, Every Container Will Be Delivered To Customer's Hands Safely and Timely.
It's a metallic based formula brake pads, it is designed for constantly start-up and brake working condition, with long service life, low wear rate, and less brake fade during the non-stop running.
Working hours: 9:00-18:00 from Monday to Friday
Address：No. 1136, East Tiaoxi Road, Qianyuan Town,Deqing County, Huzhou City,Zhejiang Province, China